Kev ceev faj rau kev teeb tsa thiab ntsuas lub tshuab ntawm nuv hom tua blasting tshuab € ï¼ ‰

Covnuv hom tua blasting tshuabfeem ntau muaj qhov pom zoo dua, thiab cov txheej txheem teeb tsa yog qhov nyuaj dua li cov cuab yeej me me. Kev txhim kho kom raug thiab ntsuas lub tshuab yog tus yuam sij txhawm rau ua haujlwm ib txwm ntawm cov cuab yeej tom qab. Thaum tsis ua haujlwm thawj zaug, cov neeg siv yuav tsum tau ua raws cov lus qhia ntawm cov neeg ua haujlwm muaj feem cuam tshuam lossis xa mus rau cov lus qhia. Kev ua haujlwm tsis tau tso cai tuaj yeem ua rau muaj kev puas tsuaj rau lub cevnuv tua blasting tshuab. Covshot blasting machine manufacturer has sorted out the precautions for installation and test machine to share with you. I hope it will be helpful to users who use the device for the first time.
1. Installation. Covnuv hom tua blasting tshuab is installed and debugged in the production plant and disassembled into several parts before being transported to the user site for installation. Although there is no pit, the foundation must be firm, the anchor bolt holes must be standardized, and the chamber body must be adjusted. After the second irrigation, the anchor bolt nuts can be tightened after solidification. After the chamber body is fixed, the various parts can be installed. Covprecautions for the installation and debugging of the relevant components are introduced below.
1. Cov cuab yeej tua blasting:
Covshot blasting device has been installed on the chamber body before leaving the factory. Please pay attention to the problems to be debugged before use. Check whether the fixed positions of the blade, the pill wheel, the directional sleeve, and the guard plate are accurate and firm, and check whether the direction of rotation is correct after power on. Then adjust the position of the directional sleeve opening. Theoretically, the angle between the front edge of the directional opening and the front edge of the blade throwing position is about 900. After fixing the position of the directional sleeve, the position of the projectile belt can be detected by hanging Place a steel plate or wooden board on the position of the workpiece facing the exit of the shot blasting machine, start the shot blasting machine, put a small amount (2-5kg) of projectiles into the blasting tube, and then stop, check whether the hit position on the steel plate is suitable for the needs, such as Close the window of the bias-adjustable directional sleeve downwards, and vice versa, until it fits, and note the position of the directional sleeve opening as a basis for future replacement of the directional sleeve.
2. Hoist thiab ntsia hlau conveyor:
Ua ntej tshaj tawm qhov ntsuas tsis tau txhawm rau txhawm rau txheeb xyuas seb lub thoob nqa thiab cov hniav sib tsoo tau ua haujlwm nyob rau hauv qhov raug, tom qab ntawd zawm txoj hlua ntawm txoj hlua kom nruj me ntsis kom nruj kom tsis txhob sib nrug, thiab tom qab ntawd ua qhov ntsuas ntsuas los xyuas kev ua haujlwm thiab xa khoom muaj peev xwm, txawm tias muaj qhov txawv txav Lub suab nrov thiab kev co, kos thiab tshem tawm cov teeb meem.
3. Pill-sand separator:
Ua ntej tshuaj xyuas seb qhov txav ntawm ram hloov pauv tau, thiab tom qab ntawd tshuaj xyuas txoj haujlwm kom raug ntawm cov phaj sib cais, tom qab ntawd thaum lub tshuab nqa tau thauj khoom thiab debugged, muaj kev txuas ntxiv ntawm cov hlau txhaj tshuaj, thiab xyuas seb cov hlau txhaj tshuaj puas ntws thiab poob thaum lub chute raug tso tawm